@jopebe said in RFID Lock Sensor: Every change to "Sensor open" should be for only let`s say 3 seconds or another adjustable time and than fall back to Default = "Sensor Locked" . Time enough e.g. to open the door...

@flopp https://forum.mysensors.org/topic/9973/mysensors-2-3-1-released

As an early holiday gift, MySensors 2.3.1 has been released. Highlights RF24: Add delay after power-up RFM69 frequency band support for India Improve transport function & debug messages Allow flash strings in present() to save RAM Release notes and changelog:...

Can you please update the table? I have made several modifications to OpenHAB. Thanks.

Great worl. Still prefer OpenHAB for my home automation, but for sensor management and OTA seems to be the way to go. Thanks!

Note: Double check your DHT11 module! The pinouts of the PCB of my DHT11 module differed from those in this article. My leftmost pin was Data out, the middle pin was VCC and the right was GND.

This thread contains comments for the article "Air Humidity Sensor - Si7021" posted on MySensors.org.

https://www.thingiverse.com/make:468039

The initial description on this page refers to BMP085. The 'Example' states it is for BMP085 with Adafruit library (linked for dowbload). The sketch uses a BME280 with library from Embedded Adventures. The Datasheet is linked for a BMP085. The...

Hi, dear how can we connect with application or something to watch and to connect with nidemcu?

@ricorico94 you’re correct. When the gateway is in server mode, multiple controllers can connect to the gateway if MY_GATEWAY_MAX_CLIENTS is defined to something larger than the default value of 1. However, things can become very confused if multiple controllers respond...

Hi I have a gateway mysensors on my RPI3 with radio RFM69HW. Is any chance to build gateway on RPI3 but also with chip ATSHA204A ? And how build it...

Perfect!!! Thanks for the update!

Great work!

Hi I just finished configuring a site map having the sample node (S_DOOR) code above as the only thing and I noticed that it only updates once (only at every restart) to the Paper UI Control, The Basic UI, and...

Thanks @fredswed, updated.

Ah I have just built a test bed with this setup however it appears the circuit diagram in the Fritizing is actually not 100% correct. The red wire from the protoboard is connected to the GND of the Pro Mini...

Technically speaking yes but I don't see the point in reinventing the wheel

I'm getting low readings. The voltage at the sensor was OK. So it had to be the calculation. In my opinion the conversion of the 1023 values into a voltage is missing which can then be calculated further. uint16_t uv...

And how to turn on ATC mode?

Okay I have nothing to lose at this point. Thanks

@mntlvr sorry, I have no experience with Vera.

hi i am using Lora SX1276 as simple transmitter and receiver. is there any library for sending and receiving the data no gateway involved only simple data transmission and reception.

If you are curious on what features are planned or what fixes are scheduled for the next release or future releases, check out the MySensors projects on Github.

@alowhum said in Dust Level Sensor: Use this one instead: https://forum.mysensors.org/topic/6404/next-generation-dust-sensor-for-mysensors/7 This one or PMS5003 are similar, PMS5003 is just bigger but technology has not changed. They have a smaller PMSA003 too, just received one and I will test it,...

@gohan yes, have done that. Thanks for your time and support!

Op Aliexpress is een nieuwe distance sensor verschenen HC-SR04P . De spec van dit model is 3-5V. Is dus ook bruikbaar met een 3.3V arduino. https://www.aliexpress.com/snapshot/0.html?spm=a2g0s.9042647.6.2.1AslKf&orderId=89862296499774&productId=32711959780

Thanks! Had to disable board outline mask as it sometimes messed up the rendering. Managed to extract dimension (and hopefully number of layers) from the gerbers which gets filled into the form.

@Wes, Here's a gist with the code for the log parser https://gist.github.com/henrikekblad/c1d652cce16eaf2ef6340eacaefc97b0

That looks like there is no communication with gateway. Did you check gw log? You could also update mysensors to latest 2.2